IAP-420 Series

IAP-420 / IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN.  It supports 802.1X and MAC filters for security control.   It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.  You are able to configure IAP-420 / IAP-420+ series by WEB interface via LAN port or WLAN interface.  In addition, IAP-420+ also provides P.D. feature on ETH1 which is fully compliant with IEEE802.3af PoE P.D. specification.  Therefore, IAP-420 / IAP-420+ series are one of the best communication solutions for wireless applications on the industrial network.

IAP-420 / IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN.  It supports 802.1X and MAC filters for security control.   It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.  You are able to configure IAP-420 / IAP-420+ series by WEB interface via LAN port or WLAN interface.  In addition, IAP-420+ also provides P.D. feature on ETH1 which is fully compliant with IEEE802.3af PoE P.D. specification.  Therefore, IAP-420 / IAP-420+ series are one of the best communication solutions for wireless applications on the industrial network.

Features

  -  High Speed Air Connectivity: WLAN interface support up to 150 Mbps link speed

  -  Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported

  -  Support X-Roaming < 100 ms

  -  Support AP/Client/Bridge/AP-Client Mode

  -  Secured Management by HTTPs

  -  Wireless connecting status monitoring

  -  Event Warning by Syslog, Email, SNMP Trap

  -  1KV isolation for PoE P.D. port of IAP-420+

  -  Rigid IP-30 housing design

  -  DIN-Rail and Wall-mount enabled

 Specifications
ORing Switch ModelIAP-420IAP-420+
Physical Ports 
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX2
PoE P.D. Port-

Present at ETH
Fully compliant with IEEE 802.3af Power Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min

WLAN Interface 
Operating Mode

AP/Client/Bridge/AP-Client

Antenna and Connector1 x External reverse SMA-type antenna connector
Radio Frequency TypeDSSS, OFDM
Modulation

IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM

Frequency Band

America / FCC:
2.412~2.462 GHz (11 channels )
Europe CE / ETSI:
2.412~2.472 GHz ( 13 channels )

Transmission Rate

802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 150 Mbps

Transmit Power

802.11b: 19dBm ±1.5dBm
802.11g: 17dBm ±1.5dBm
802.11n(2.4G@20MHz): 16.5dBm ±1.5dBm
802.11n(2.4G@40MHz): 14.5dBm ±1.5dBm

Receiver Sensitivity

802.11b: -90dBm ±2dBm@1Mbps
802.11g: -72dBm ±2dBm@54Mbps
802.11n(2.4G@40MHz,MCS7): -68dBm ±2dBm

Encryption Security

WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption

Wireless SecuritySSID broadcast disable and enable
Protocol Support 
ProtocolARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
LED Indicators 
Power Indicator

LED x 3, PWR 1, 2, (PoE):
Green On: Power is on and functioning Normally.

10/100Base-T(X) RJ45 Port IndicatorLED x 2 , Green for port Link/Act at 100Mbps.
WLAN LEDsWLAN Link /ACT: Green: Blinking
Power 
Redundant Input PowerDual DC inputs. 12~48VDC on 4-pin terminal block
Power Consumption (Typ.)4 Watts
Overload Current ProtectionPresent
Reverse Polarity ProtectionPresent
Physical Characteristics 
EnclosureIP-30
Dimensions (W x D x H)41(W)x81(D)x95(H) mm
Weight (g)292 g297 g
Environmental 
Storage Temperature-40 to 85°C (-40 to 185°F)
Operating Temperature-10 to 60°C(14 to 140°F)
Operating Humidity5% to 95% Non-condensing
Regulatory Approvals 
EMIFCC Part 15, CISPR (EN55022) class A
EMS

IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT), IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8, IEC61000-4-11

ShockIEC60068-2-27
Free FallIEC60068-2-31
VibrationIEC60068-2-6
SafetyEN60950-1
Warranty5 years

Bình luận